Is anyone using Setlist maker or Band helper to do program switching on the Integra? I'm struggling with getting it configured properly. Would it be possible to see how you are sending your settings to the integra?
-Dave
Anyone using Setlistmaker or Bandhelper?
Re: Anyone using Setlistmaker or Bandhelper?
I use setlist maker for my X7. I just use the Bank CCs and PC commands and it works fine.
Not sure if this helps!
Cheers
Andy
Not sure if this helps!
Cheers
Andy
Re: Anyone using Setlistmaker or Bandhelper?
For some reason the Integra doesn't recognize what I'm sending it. Using what I think are the correct parameters. It should be as simple as you say, so I think I'm missing something really simple.
-Dave
-Dave
Re: Anyone using Setlistmaker or Bandhelper?
What exactly are you sending then?
What you need to send is:
Control command number 00, with MSB value
Control command number 32, with LSB value
Program Change command with PC value
What you need to send is:
Control command number 00, with MSB value
Control command number 32, with LSB value
Program Change command with PC value
Re: Anyone using Setlistmaker or Bandhelper?
Here is how I set it up. Channel 16 just goes to all 0000. So it is receiving something, just not sure what.
- Attachments
-
- bandhelpercapture.JPG (34.13 KiB) Viewed 1671 times
Re: Anyone using Setlistmaker or Bandhelper?
It's not clear to me what you mean with "Channel 16 just goes to all 0000".
I would think that if you send instructions to the Integra on Channel 16, you should set the receiving channel on the Integra itself also on that channel.
And depending on how you connect your device to the Integra, MIDI or USB cable, you have to make some settings accordingly on the Integra. (page 45 in the manual)
I would think that if you send instructions to the Integra on Channel 16, you should set the receiving channel on the Integra itself also on that channel.
And depending on how you connect your device to the Integra, MIDI or USB cable, you have to make some settings accordingly on the Integra. (page 45 in the manual)
Re: Anyone using Setlistmaker or Bandhelper?
This is what I mean. When I send the code from the Integra setup, it changes part 16 to 0000.
I went through the setup on page 45. I tried the midi thru each way with the same result. Something just isn't setup right.
I did find a way to catch the raw midi and was able to switch settings that way. Pretty rough way to do it but if the program changes don't work it may be the only way to have this work.
Thanks!
I went through the setup on page 45. I tried the midi thru each way with the same result. Something just isn't setup right.
I did find a way to catch the raw midi and was able to switch settings that way. Pretty rough way to do it but if the program changes don't work it may be the only way to have this work.
Thanks!
- Attachments
-
- IMG_0002.JPG (827.75 KiB) Viewed 1643 times
-
- IMG_0003.JPG (933.37 KiB) Viewed 1643 times
Re: Anyone using Setlistmaker or Bandhelper?
Would you mind post a screen shot of how you have one of your setups on Setlistmaker?
Re: Anyone using Setlistmaker or Bandhelper?
I do have Setlistmaker, but without the midi functionality, so I can't help you with that.
But I do had the same problem when I was programming the Behringer FCB1010 to connect with the Integra.
And it occurs to me now that you could try to put the needed Control Commands into the dedicated fields in SLM instead of in the Program Changes fields.
So: in the Control Changes part, create two lines for the Integra.
In the first line, enter the these values in the two fields: 00 and 95 (that is your MSB value)
In the second line, enter the these values in the two fields: 32 and 64 (that is your LSB value)
I'm not sure whether you should remove the MSB/LSB values in the Program Changes part and keep only the Program change value 1 there. I would try that first anyway.
But I do had the same problem when I was programming the Behringer FCB1010 to connect with the Integra.
And it occurs to me now that you could try to put the needed Control Commands into the dedicated fields in SLM instead of in the Program Changes fields.
So: in the Control Changes part, create two lines for the Integra.
In the first line, enter the these values in the two fields: 00 and 95 (that is your MSB value)
In the second line, enter the these values in the two fields: 32 and 64 (that is your LSB value)
I'm not sure whether you should remove the MSB/LSB values in the Program Changes part and keep only the Program change value 1 there. I would try that first anyway.