problem CV/Gate
problem CV/Gate
Hi,
I try to control my modular system with the Fantom, but nothing is happening.
I connected the cv and gate output to the desired inputs on the modules and followed the instructions in the manual. I select zone 1, assigned CV/Gate to zone 1, but I'm not getting a signal out (both CV/Gate 1 and 2).
I hope I am just missing a crucial setting or something and it isn't a mallfunction that needs fixing.
I checked the other outputs, but it's just the CV/Gate.
I hope you guys prove me doing something stupid and I don't have to send it back to the shop.
I try to control my modular system with the Fantom, but nothing is happening.
I connected the cv and gate output to the desired inputs on the modules and followed the instructions in the manual. I select zone 1, assigned CV/Gate to zone 1, but I'm not getting a signal out (both CV/Gate 1 and 2).
I hope I am just missing a crucial setting or something and it isn't a mallfunction that needs fixing.
I checked the other outputs, but it's just the CV/Gate.
I hope you guys prove me doing something stupid and I don't have to send it back to the shop.
Re: problem CV/Gate
😃😃😃😃
Zone set to EXT...?
Page 104, Reference Manual...
Controlling an External MIDI Device.
This unit’s knob operations and keyboard performance can be transmitted as MIDI messages from the MIDI OUT connector and from USB MIDI OUT.
Keyboard data can be output from the CV/GATE OUT jacks as CV/GATE signals. By setting a specific zone to “EXT,” you can use that zone for controlling an external MIDI device.
Since those instructions were given before the ADVANCED configuration become available, I understand not only EXT (green lit), but BOTH (yellow lit) could also be used instead.
Also, there are settings under SYSTEM and SCENE...
🎹🎹🎹🎹
Zone set to EXT...?
Page 104, Reference Manual...
Controlling an External MIDI Device.
This unit’s knob operations and keyboard performance can be transmitted as MIDI messages from the MIDI OUT connector and from USB MIDI OUT.
Keyboard data can be output from the CV/GATE OUT jacks as CV/GATE signals. By setting a specific zone to “EXT,” you can use that zone for controlling an external MIDI device.
Since those instructions were given before the ADVANCED configuration become available, I understand not only EXT (green lit), but BOTH (yellow lit) could also be used instead.
Also, there are settings under SYSTEM and SCENE...
🎹🎹🎹🎹
Re: problem CV/Gate
Thanks for the effort!
I did all this, well I think I did, but I will check some things again.
I did all this, well I think I did, but I will check some things again.
Re: problem CV/Gate
Let's know your achievements, please.
I am anxious to being able to tell you that " I have a faint idea that you are happy with your CV/Gate. ;-) " as you did with my pedals...😃😃😃😃
I am anxious to being able to tell you that " I have a faint idea that you are happy with your CV/Gate. ;-) " as you did with my pedals...😃😃😃😃
Re: problem CV/Gate
Thanks!
I will do some more tests this week and if there is no change I will send a message to Roland support.
Last year I had a problem and that was solved by them in a good way, so I'm confident there will be a solution one way or the other.
I will do some more tests this week and if there is no change I will send a message to Roland support.
Last year I had a problem and that was solved by them in a good way, so I'm confident there will be a solution one way or the other.
Re: problem CV/Gate
Ohhh...
Still no advance...Ok.
What issue you mention was that of last year that was fixed through Roland Support, if you please ?
I am struggled with the Analog Filter...
Still no advance...Ok.
What issue you mention was that of last year that was fixed through Roland Support, if you please ?
I am struggled with the Analog Filter...
Re: problem CV/Gate
The Fantom occasionally froze during startup.
Over time it occurred more frequent so in the end I had to send it in for repair.
It came back two weeks later so no complains about their service.
About the analog filter.
I know I struggled with it either.
I don't use it often, but the problem was in a routing setting.
I don't recall any details, but I will look at it when I do my CV/Gate checks.
I will come back to it later.
Over time it occurred more frequent so in the end I had to send it in for repair.
It came back two weeks later so no complains about their service.
About the analog filter.
I know I struggled with it either.
I don't use it often, but the problem was in a routing setting.
I don't recall any details, but I will look at it when I do my CV/Gate checks.
I will come back to it later.
Re: problem CV/Gate
Lovely, thank you.Tom_1970 wrote: ↑21:12, 3 August 2022 The Fantom occasionally froze during startup.
Over time it occurred more frequent so in the end I had to send it in for repair.
It came back two weeks later so no complains about their service.
About the analog filter.
I know I struggled with it either.
I don't use it often, but the problem was in a routing setting.
I don't recall any details, but I will look at it when I do my CV/Gate checks.
I will come back to it later.
😃😃😃😃
Re: problem CV/Gate
@FGM Make sure that the Analog Filter is connected to the Main Output in the effect edit menu.
I hope this will do the trick for you.
I hope this will do the trick for you.
Re: problem CV/Gate
Very kind of you, Tom_1970...😃😃😃😃
I did that long ago and didn't work.
In fact it stops all sounds in Fantom.
The helping hand for my analog filter question ends here, please, as I don't feel like going through the same check points over and over in an endless circle of madness reaching nowhere...
Thank you, thank you, thank you...
🎹🎹🎹🎹
I did that long ago and didn't work.
In fact it stops all sounds in Fantom.
The helping hand for my analog filter question ends here, please, as I don't feel like going through the same check points over and over in an endless circle of madness reaching nowhere...
Thank you, thank you, thank you...
🎹🎹🎹🎹
Re: problem CV/Gate
You're welcome.
Pity that it didn't work out.
Well, my experiments didn't work either, so I'am afraid I have to contact support after the weekend.
Pity that it didn't work out.
Well, my experiments didn't work either, so I'am afraid I have to contact support after the weekend.
Re: problem CV/Gate
Cannot say I am seeing you very cheerful with the experiments...
The hard part is discovering a potential issue after many months of use, remembering when I went buying hundreds of CDs at a time (typical Full Collection of...) just to discover a pair of them with damage some three years later.
Another try...?
https://youtu.be/mVRsE_K_OrY
https://youtu.be/klkgszhhjbI
Re: problem CV/Gate
I already watched those, but thanks anyway.
Whatever the trouble is, I'm pretty confident it will be sorted out.
I just don't like packing and sending my gear out.
Whatever the trouble is, I'm pretty confident it will be sorted out.
I just don't like packing and sending my gear out.
Re: problem CV/Gate
An update.
I contacted Roland support and after some tips and test they advised me to send it bak to Thomann.
Just received the Fantom back after it being away for a fourth night.
Hooked it up, restored my backup files and connected it to my modular.
It all works like a charm!
Now I can experiment with the Fantom/Matriarch combination it all started with.
I contacted Roland support and after some tips and test they advised me to send it bak to Thomann.
Just received the Fantom back after it being away for a fourth night.
Hooked it up, restored my backup files and connected it to my modular.
It all works like a charm!
Now I can experiment with the Fantom/Matriarch combination it all started with.